Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Magtec Electric Gates lisburn

The following info will discuss all you require to know to determine which 'Linear Ram' electric gate motors are best for you - Electric Gate Installers Lisburn. Before picking a suitable motor you will need some standard information about your gate set up and environment. The information can then be used to cross referral with the motor specifications and manufacturer guidelines. Electric Gates.

Both types can be wired straight from your mains power. The number of gate operations per hour will determine which type of power output is required. Motors are created to run within a specific capability (operations per hour). Picking a motor compatible with your expected usage is necessary for its toughness and safe operation.

If the electric gate is planned to be in usage more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electric gate motors which enables more extensive use. 24v electrical gate motors tend to be used on commercial/communal facilities, where as 230v on standard homes.

Electric Gates Repairs Near Me lisburn



Each producer will have a variety of electric gate motors which run approximately a maximum weight. The weight limit ensures the motor will operate the gate/s in a trusted and safe manner by offering the best quantity of torque. Under-powered motors will not hit their opening/closing points and over-powered motors might cause damage to eviction and/or hinges. Electric Gates.

The motor mechansim will vary in size to suit the width of eviction (Electric Gates). Its essential to note the motor 'max' width can be higher than your gate (to a certain level as per producer guidelines) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not gain the required leverage to reach its totally open or closed positions.

How Much Are Electric Gates lisburnCommercial Electric Gates lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most common type of on-gate electrical motors are linear rams, they cover practically all gate formats. Direct Rams run the gates through a curved trajectory.

Metal Electric Gates lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are determined as follows: Total stroke length (minus 15-20mm depending on the maker - the motors can not utilize their overall operating length so an arrangement is provided) divided by 2. This then provides you the A/B measurements which form the pivot indicate mount the motor for optimum mechanical take advantage of.

Complete growth 980mm minus total retraction 665mm = 315mm stroke length (Wooden Electric Gates Lisburn). Provision for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To gain the optimal geometry the motor's pivot point must be placed 150mm x 150mm from the centre of the gate hinge.

Setting up the motor outside of these tolerences will put the motor at danger and also void the service warranty. Typically speaking if A is decreased, B will be increased by the very same amount and vice versa to stay within the motors permitted geometry - Electric Gates.

Electric Gate Systems lisburn

The D measurement just comes into play for side hung gates. The D measurements are comprehensive alongside the A & B measurements within the install parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position procedures greater than defined, installing the motor is not possible. For the basic factor - the motor itself will come into contact with the corner of the pillar and avoid the gate from opening or closing.

Electric Sliding Gate Cost lisburnResidential Electric Gate Kits lisburn


The bracket must be installed so the pivot point of the motor (the pin) accompanies the A & B measurements (And D if side hung). Generally the bracket is either bolted or welded to the pillar or post. You will require the following measurements to figure out whether the motor bracket can be straight mounted to the post. Electric Gates.

Electric Gates County Down lisburn

If your pillar width is too little to mount the motor bracket straight (which is really typical when retro fitting gate motors) then an additional post might be needed or an adjusted bracket. A lot of electrical gate motors require a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Electric Gate Entry Systems Lisburn

Published Sep 19, 22
4 min read

Electric Gate Company Near Me Lisburn

Published Sep 18, 22
4 min read