Electric Gates for Driveways Lisburn

Published Sep 16, 22
4 min read

Sliding Electric Gates lisburn

The following information will describe all you need to know to identify which 'Linear Ram' electrical gate motors are best for you - Electric Gates NI Lisburn. Before selecting an appropriate motor you will need some basic info about your gate set up and environment. The information can then be used to cross reference with the motor specifications and maker standards. Electric Gates.

Both types can be wired straight from your mains power. The variety of gate operations per hour will figure out which kind of power output is required. Motors are created to operate within a particular capacity (operations per hour). Choosing a motor suitable with your expected usage is essential for its sturdiness and safe operation.

If the electrical gate is meant to be in usage more frequntly (+15 times per hour) then a 24v system is recommended. 24v systems run cooler than 230v electrical gate motors which permits more extensive use. 24v electric gate motors tend to be used on commercial/communal properties, where as 230v on basic homes.

Sliding Electric Gates lisburn



Each producer will have a range of electrical gate motors which operate up to a maximum weight. The weight limitation guarantees the motor will operate the gate/s in a reliable and safe manner by offering the correct amount of torque. Under-powered motors will not strike their opening/closing points and over-powered motors may trigger damage to eviction and/or hinges. Electric Gates.

The motor mechansim will differ in size to fit the width of eviction (Electric Gates). Its important to note the motor 'max' width can be greater than your gate (to a specific level as per manufacturer guidelines) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not gain the required utilize to reach its totally open or closed positions.

Electric Gates Lisburn lisburnCame Electric Gates lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most typical form of on-gate electrical motors are direct rams, they cover nearly all gate formats. Linear Rams operate the gates through a curved trajectory. This forms the geometry of the the linear ram through its opening and closing cycle. Electric Gates. For direct rams the geometry is defined by 2 measurements: the 'A & B' measurements.

Electric Gate Installation lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are calculated as follows: Total stroke length (minus 15-20mm depending on the producer - the motors can not use their overall operating length so an arrangement is provided) divided by 2. This then gives you the A/B measurements which form the pivot point to install the motor for optimum mechanical take advantage of.

Full growth 980mm minus total retraction 665mm = 315mm stroke length (Electric Gates Kits Lisburn). Provision for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To get the optimum geometry the motor's pivot point ought to be positioned 150mm x 150mm from the centre of eviction hinge.

Installing the motor outside of these tolerences will put the motor at risk and also void the service warranty. Normally speaking if A is reduced, B will be increased by the exact same amount and vice versa to remain within the motors permitted geometry - Electric Gates.

Electric Gate Cost lisburn

The D dimension just enters play for side hung gates. The D measurements are detailed together with the A & B dimensions within the set up parmater tables. Electric Gates. The D measurement is the distance from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position measures greater than defined, installing the motor is not possible. For the basic reason - the motor itself will come into contact with the corner of the pillar and prevent the gate from opening or closing.

Electric Sliding Gates lisburnHow Much Do Electric Gates Cost lisburn


The bracket should be mounted so the pivot point of the motor (the pin) coincides with the A & B measurements (And D if side hung). Generally the bracket is either bolted or bonded to the pillar or post. You will require the following measurements to figure out whether the motor bracket can be straight installed to the post. Electric Gates.

Electric Gate Installation lisburn

If your pillar width is too small to mount the motor bracket directly (which is extremely typical when retro fitting gate motors) then an extra post might be needed or an adjusted bracket. Many electrical gate motors require a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Electric Gate Entry Systems Lisburn

Published Sep 19, 22
4 min read

Electric Gate Company Near Me Lisburn

Published Sep 18, 22
4 min read