Electric Gate Near Me Lisburn

Published Aug 31, 22
4 min read

Sliding Electric Gates lisburn

The following details will discuss all you need to know to identify which 'Direct Ram' electrical gate motors are best for you - Electric Drive Gates Lisburn. Before selecting a proper motor you will need some basic info about your gate set up and environment. The information can then be used to cross reference with the motor requirements and producer standards. Electric Gates.

Both types can be wired straight from your mains power. The number of gate operations per hour will identify which kind of power output is needed. Motors are designed to operate within a specific capacity (operations per hour). Selecting a motor compatible with your anticipated usage is vital for its toughness and safe operation.

If the electrical gate is intended to be in usage more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electric gate motors which permits more extensive usage. 24v electric gate motors tend to be used on commercial/communal premises, where as 230v on standard houses.

Electric Gate Motors lisburn



Each maker will have a series of electric gate motors which operate up to a maximum weight. The weight limitation ensures the motor will run the gate/s in a trusted and safe way by offering the right quantity of torque. Under-powered motors will not strike their opening/closing points and over-powered motors may trigger damage to the gate and/or hinges. Electric Gates.

The motor mechansim will differ in size to suit the width of eviction (Electric Gates). Its essential to note the motor 'max' width can be higher than your gate (to a particular degree as per producer standards) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not get the required utilize to reach its fully open or closed positions.

Electric Gates Northrn Ireland lisburnElectric Security Gates lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most typical kind of on-gate electric motors are direct rams, they cover nearly all gate formats. Linear Rams operate the gates through a curved trajectory. This forms the geometry of the the linear ram through its opening and closing cycle. Electric Gates. For direct rams the geometry is specified by 2 measurements: the 'A & B' measurements.

Residential Electric Gate Kits lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are determined as follows: General stroke length (minus 15-20mm depending upon the producer - the motors can not utilize their overall operating length so an arrangement is provided) divided by 2. This then provides you the A/B measurements which form the pivot indicate install the motor for optimum mechanical leverage.

Full expansion 980mm minus total retraction 665mm = 315mm stroke length (Electric Sliding Gate Kit Lisburn). Arrangement for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To gain the optimum geometry the motor's pivot point must be positioned 150mm x 150mm from the centre of eviction hinge.

Setting up the motor outside of these tolerences will put the motor at danger and also void the warranty. Usually speaking if A is decreased, B will be increased by the same quantity and vice versa to remain within the motors permitted geometry - Electric Gates.

Electric Gates Lisburn lisburn

The D dimension only comes into play for side hung gates. The D measurements are comprehensive alongside the A & B dimensions within the install parmater tables. Electric Gates. The D measurement is the distance from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position procedures greater than defined, setting up the motor is not possible. For the easy reason - the motor itself will enter into contact with the corner of the pillar and avoid eviction from opening or closing - Electric Gates. This normally occurs with over-sized pillars. If this is the case then an articulated arm would be a preferable choice.

Sliding Electric Gate lisburnElectric Gate Fobs lisburn


The bracket should be mounted so the pivot point of the motor (the pin) accompanies the A & B measurements (And D if side hung). Usually the bracket is either bolted or bonded to the pillar or post. You will need the following measurements to figure out whether the motor bracket can be straight mounted to the post. Electric Gates.

Electric Gates Lisburn lisburn

If your pillar width is too little to install the motor bracket straight (which is extremely common when retro fitting gate motors) then an extra post might be needed or an adapted bracket. Most electric gate motors require a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Electric Gate Entry Systems Lisburn

Published Sep 19, 22
4 min read

Electric Gate Company Near Me Lisburn

Published Sep 18, 22
4 min read