Electric Gate Installer Near Me Lisburn

Published Sep 06, 22
4 min read

Electric Gates For Driveways lisburn

The following info will discuss all you need to understand to identify which 'Linear Ram' electric gate motors are best for you - Electric Gate Repair Lisburn. Prior to selecting a suitable motor you will need some fundamental details about your gate set up and environment. The details can then be utilized to cross reference with the motor specifications and producer guidelines. Electric Gates.

Both types can be wired directly from your mains power. The number of gate operations per hour will determine which type of power output is needed. Motors are designed to run within a particular capacity (operations per hour). Selecting a motor suitable with your expected usage is necessary for its toughness and safe operation.

If the electrical gate is meant to be in usage more frequntly (+15 times per hour) then a 24v system is recommended. 24v systems run cooler than 230v electrical gate motors which enables more extensive use. 24v electric gate motors tend to be utilized on commercial/communal facilities, where as 230v on standard homes.

Electric Gate Installers Near Me lisburn



Each maker will have a range of electric gate motors which operate up to a maximum weight. The weight limit ensures the motor will run the gate/s in a trustworthy and safe way by providing the correct amount of torque. Under-powered motors will not strike their opening/closing points and over-powered motors may cause damage to eviction and/or hinges. Electric Gates.

The motor mechansim will differ in size to match the width of the gate (Electric Gates). Its important to keep in mind the motor 'max' width can be greater than your gate (to a particular extent based on maker standards) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not get the required utilize to reach its completely open or closed positions.

Electric Garden Gates lisburnSliding Electric Gates Installers Near Me lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most typical type of on-gate electric motors are linear rams, they cover nearly all gate formats. Linear Rams run the gates through a curved trajectory.

Electric Gate Installers lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are computed as follows: Total stroke length (minus 15-20mm depending upon the maker - the motors can not utilize their total operating length so a provision is offered) divided by 2. This then offers you the A/B measurements which form the pivot indicate install the motor for maximum mechanical leverage.

Complete expansion 980mm minus complete retraction 665mm = 315mm stroke length (Electric Gates Repairs Near Me Lisburn). Arrangement for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To acquire the maximum geometry the motor's pivot point must be positioned 150mm x 150mm from the centre of eviction hinge.

Installing the motor outside of these tolerences will put the motor at threat and likewise void the guarantee. Typically speaking if A is minimized, B will be increased by the same quantity and vice versa to remain within the motors allowed geometry - Electric Gates.

Electric Gates Ni lisburn

The D measurement just enters into play for side hung gates. The D measurements are in-depth along with the A & B measurements within the install parmater tables. Electric Gates. The D measurement is the distance from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position steps higher than specified, setting up the motor is not possible. For the easy factor - the motor itself will come into contact with the corner of the pillar and prevent the gate from opening or closing.

Electric Sliding Gates lisburnElectric Gate Installer Near Me lisburn


The bracket should be installed so the pivot point of the motor (the pin) accompanies the A & B measurements (And D if side hung). Normally the bracket is either bolted or welded to the pillar or post. You will require the following measurements to determine whether the motor bracket can be straight mounted to the post. Electric Gates.

Electric Gate Repairs lisburn

If your pillar width is too little to mount the motor bracket straight (which is extremely common when retro fitting gate motors) then an additional post might be needed or an adjusted bracket. A lot of electrical gate motors need a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Electric Gate Entry Systems Lisburn

Published Sep 19, 22
4 min read

Electric Gate Company Near Me Lisburn

Published Sep 18, 22
4 min read