Electric Gate Fobs Lisburn

Published Sep 13, 22
4 min read

Wooden Electric Sliding Gates For Driveways lisburn

The following info will describe all you require to know to figure out which 'Linear Ram' electrical gate motors are best for you - Electric Fence Gate Lisburn. Before choosing a suitable motor you will require some fundamental details about your gate established and environment. The details can then be used to cross referral with the motor requirements and manufacturer standards. Electric Gates.

The number of gate operations per hour will identify which type of power output is required. Choosing a motor compatible with your expected usage is vital for its sturdiness and safe operation.

If the electrical gate is planned to be in use more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electrical gate motors which allows for more intensive use. 24v electric gate motors tend to be utilized on commercial/communal facilities, where as 230v on basic homes.

Electric Gates lisburn



Each producer will have a range of electrical gate motors which operate up to a maximum weight. The weight limit makes sure the motor will operate the gate/s in a trustworthy and safe way by supplying the ideal amount of torque. Under-powered motors will not strike their opening/closing points and over-powered motors may cause damage to the gate and/or hinges. Electric Gates.

The motor mechansim will differ in size to suit the width of eviction (Electric Gates). Its crucial to keep in mind the motor 'max' width can be greater than your gate (to a particular level as per maker guidelines) however not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not get the required leverage to reach its completely open or closed positions.

Driveway Gates Electric lisburnElectric Gates For Driveways lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most typical kind of on-gate electric motors are linear rams, they cover practically all gate formats. Direct Rams operate the gates through a curved trajectory.

Electric Gate Installation lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are calculated as follows: Total stroke length (minus 15-20mm depending on the manufacturer - the motors can not utilize their total operating length so a provision is given) divided by 2. This then gives you the A/B measurements which form the pivot point to mount the motor for optimum mechanical utilize.

Full expansion 980mm minus complete retraction 665mm = 315mm stroke length (Electric Gate Controller Lisburn). Provision for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To get the maximum geometry the motor's pivot point must be placed 150mm x 150mm from the centre of the gate hinge.

Setting up the motor outside of these tolerences will put the motor at threat and likewise void the guarantee. Typically speaking if A is reduced, B will be increased by the same quantity and vice versa to stay within the motors allowed geometry - Electric Gates.

Sliding Electric Gates Installers Near Me lisburn

The D dimension just enters into play for side hung gates. The D measurements are detailed along with the A & B measurements within the install parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position measures greater than specified, setting up the motor is not possible. For the basic reason - the motor itself will come into contact with the corner of the pillar and prevent the gate from opening or closing.

Electric Farm Gate lisburnElectric Gates Near Me lisburn


The bracket must be mounted so the pivot point of the motor (the pin) coincides with the A & B measurements (And D if side hung). Typically the bracket is either bolted or bonded to the pillar or post. You will require the following measurements to identify whether the motor bracket can be straight installed to the post. Electric Gates.

Modern Electric Gates lisburn

If your pillar width is too small to mount the motor bracket directly (which is really typical when retro fitting gate motors) then an extra post might be needed or an adapted bracket. Many electrical gate motors require a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Came Electric Gates Lisburn

Published Sep 19, 22
4 min read

Electric Gate Entry Systems Lisburn

Published Sep 19, 22
4 min read

Electric Gate Company Near Me Lisburn

Published Sep 18, 22
4 min read